Internatrix Alarm System - Motorcycle-Journal Forums

Navy_p503 · 10-07-2007, 07:52 PM

Hey everyone, I finished installing my Internatrix Alarm on the bike yesterday. Install was pretty easy and took about a total of 3 hours. One hour to figure out where everything was going to go and to test it out before installation. Two hours to wire it up and put everything back together. I only needed to take the rear cowl off to run the wires. Could've done it without removing anything but I wanted to clean all the wires and run them where the stock harness is. The installation directions were very good, the only part that was lacking was hooking up the ignition disable feature. But since there are so many ways to do it they can't include them all. I've tested all the functions and it works very well, haven't really tested out the range yet though, once I do I'll post what I find. I'll post a couple pics tomorrow on where I installed the control unit and everything. If anyone has any questions let me know

robertc729 · 10-08-2007, 04:59 PM

Navy_p503 · 10-09-2007, 08:24 PM

Here's the pics,
I still haven't figured out where I'm going to put the antenna or the armed LED, but I'll wait until I get the bike back from getting all the stuff repaired that the @#@#$#$%#%^ did to it when they stole it. The top arrow is the antenna, the bottom is the control unit. The underside of the seat has the proximity sensor.

10-07-2007, 07:52 PM	#1 (permalink)
Navy_p503 Third gear and cruising Joined: Jun 2007 Bike: 94 Yamaha YZ 250, 2000 Suzuki Bandit 600s Location: Fort Collins, Co Posts: 470	Internatrix Alarm System Hey everyone, I finished installing my Internatrix Alarm on the bike yesterday. Install was pretty easy and took about a total of 3 hours. One hour to figure out where everything was going to go and to test it out before installation. Two hours to wire it up and put everything back together. I only needed to take the rear cowl off to run the wires. Could've done it without removing anything but I wanted to clean all the wires and run them where the stock harness is. The installation directions were very good, the only part that was lacking was hooking up the ignition disable feature. But since there are so many ways to do it they can't include them all. I've tested all the functions and it works very well, haven't really tested out the range yet though, once I do I'll post what I find. I'll post a couple pics tomorrow on where I installed the control unit and everything. If anyone has any questions let me know __________________ 2003 Mazda Protege 5 navy_p503@hotmail.com

10-09-2007, 08:24 PM	#3 (permalink)
Navy_p503 Third gear and cruising Joined: Jun 2007 Bike: 94 Yamaha YZ 250, 2000 Suzuki Bandit 600s Location: Fort Collins, Co Posts: 470	Here's the pics, I still haven't figured out where I'm going to put the antenna or the armed LED, but I'll wait until I get the bike back from getting all the stuff repaired that the @#@#$#$%#%^ did to it when they stole it. The top arrow is the antenna, the bottom is the control unit. The underside of the seat has the proximity sensor. Attached Thumbnails __________________ 2003 Mazda Protege 5 navy_p503@hotmail.com Last edited by Navy_p503; 10-09-2007 at 08:28 PM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Installing an Alarm	onewolf	The Boulevard	5	04-19-2007 09:30 PM
Im looking for an alarm system	RicoChet	Cruisers	8	08-15-2006 05:44 PM
HELP!!! '04 GSX-R 1000 Alarm	sooerscreename	Sportbikes & Sport-tourers	0	03-01-2006 04:19 PM
Motorcycle Alarm???	GothamEMS	Sportbikes & Sport-tourers	5	08-23-2004 09:07 PM

10-08-2007, 04:59 PM	#2 (permalink)
robertc729 Forensic Bug Splatter Analyst Joined: Mar 2006 Bike: 05 Boulevard C50 LE, 06 S40 (wife's bike) Location: Lexington, KY Posts: 4,086

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)